CSB塑料轴承产品
banner
banner
banner
CSB塑料轴承产品05
CSB塑料轴承产品04
WR02 Stainless steel linear guides, double round rail

Product properties

● Dual guide rails made of stainless steel 316Ti 

● Good corrosion resistance 

● Resistance to dirt with LIN liners

● Maintenance-free and no noise

● Standard fitting width



WR02 Stainless steel linear guides, double round rail
Dimensions

Eccentric forces

● Maximum 2:1 ratio

● 1x = bearing separation on same shaft 

● 2x = distance from shaft to load or force

CSB-LIN®直线轴承安装法则

● CAUTION: uneven motion or even system blockage will occur if the 2:1 ratio is exceeded !

This principle is NOT load dependent! It is NOT due to edge loading. It is also NOT dependent on the driving force used! The greater the distance between the drive and guide bearings, the higher the degree of wear and required drive force.

There may be other factors that add to the braking effect, but the coefficient of friction is the main cause.

● NOTE: The Rule(2:1) is based on the static friction value of 0.25 theoretically, However, Additional lubrication can help to drop friction and extend the 2:1 ratio.

● If you have any questions on design and/or assembly, please contact our application engineers.


LIN-11K Plastic linear bearing liners
LIN-11K Plastic linear bearing liners

● Opening design sliding liners
● Self-lubricating and dust resistance
● Made of anti-wear material EPB13,MN2,EPB5

more
WRU01 Stainless steel guide rail sliding blocks
WRU01 Stainless steel guide rail sliding blocks

● Fitted standard liners EPB13 

● Housing made of stainless steel 316Ti

● Good corrosion resistance

● For WR ES single and dual guide rails

more

CSB-LMS®WRU01 Stainless steel guide rail sliding blocks

Type PDF
Size 91KB
Time 11-2022
No. CSB/CAT.062E
download

917

CSB-LMS®WR02 Stainless steel linear guides, double round rail

Type PDF
Size 106KB
Time 11-2022
No. CSB/CAT.062E
download

883

CSB-LIN® Plastic Linear Bearings Finder[V2.0] including LIN plastic linear bearings and LINP precision linear bearings. The system is based on the analysis and calculation of a large number of test data in CSB® laboratory. You can calculations bearing data by entering parameters such as bearing load, speed, temperature and position information, The system will output bearing adaptation data and min. driving force.
Because the system calculate and analyze based on lab data, it can't exactly meet the ractual use requirements absolutly. The system data verification has certain limitations; CSB® recommends that the bearing must be tested again to verify whether it meets the actual use requirements.
CSB-LIN® Plastic Linear Bearings Finder output data information is only for design reference, and can not be used as the final standard for determining the bearing material conformity, If you have any questions, please contact CSB® sales engineers.

+86-400-6633-096

Product News

Customer Services

Fast Services

CSB® More products
Precision shafts
Precision shafts

AS: Hard anodized aluminum shaft, the best shaft for LIN linear bearings; CS: Hard-chromed steel shaft, the effective-cost shaft; ES: 304 Stainless steel shaft, the best for chemical liquid; Shaft end processing service...

more
Supported shafts
Supported shafts

Compact and low high design support;

Standard design support;

3 materials shaft: Hard anodized aluminum shaft, Hardchromed steel shaft, 304 Stainless steel shaft;

more
WR01 Single round linear guide rails
WR01 Single round linear guide rails

● Single guide rails made of aluminum

● Hard anodized surface

● Weight saving and no noise

● Variable width can be fitted

more
WR02 Double round linear guide rails
WR02 Double round linear guide rails

● Dual guide rails made of aluminum

● Hard anodized surface

● Weight saving and no noise

● Standard fitting width

more
WR01 Stainless steel linear guides, single round rail
WR01 Stainless steel linear guides, single round rail

● Single guide rails made of stainless steel 316Ti

● Good corrosion resistance 

● Resistance to dirt with LIN liners

● Variable width can be fitted

more